8E8415 SHANK AS-RIPPER Caterpillar parts
854G, D10N, D10R, D10T, D10T2
Rating:
Alternative (cross code) number:
CA8E8415
8E-8415
8E8415
CA8E8415
8E-8415
8E8415
Weight: 975 pounds 442 kg.
TRACK-TYPE TRACTOR, WHEEL DOZER,
Compatible equipment models: 8E8415:
Number on catalog scheme:
6
For full view, you need register
Information:
Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that the mating surfaces of fuel injection pump (1) and fuel transfer pump (2) are clean and free from damage.
Illustration 1 g01335045
Install a new O-ring seal (11) to fuel transfer pump (2) . Lubricate the O-ring seal with clean engine oil.
Illustration 2 g01335043
Align the holes in fuel transfer pump (2) with dowels (10) in fuel injection pump (1) . Install the fuel transfer pump to the fuel injection pump.
Illustration 3 g01334899
Use an allen wrench with a ball end to install the allen head screws (3) . Tighten the allen head screws to a torque of 30 N m (22 lb ft).
Remove the plugs and the caps from the ports and tube assemblies.
Install tube assembly (4) for the engine oil supply to fuel injection pump (1) . Install new washers to the banjo bolt for oil supply tube assembly. Install the banjo bolt to the cylinder block. Tighten both connectors to a torque of 15 N m (11 lb ft).
Install tube assembly (8) for the fuel return to fuel transfer pump (2) and to the cylinder head. Tighten both banjo bolts to a torque of 21 N m (15 lb ft).
Install a new O-ring seal to connector (6) . Install connector (6) to fuel transfer pump (2) . Tighten the connector to torque of 15 N m (11 lb ft).
If necessary, install a new O-ring seal to connector (9) and install connector (9) to fuel transfer pump (2) . Tighten the connector to torque of 15 N m (11 lb ft).
Connect plastic tube assembly (5) to the outlet of fuel transfer pump (2) .
Install plastic tube assembly (7) to fuel transfer pump (2) .
Turn the fuel supply to the ON position.
Remove the air from the fuel system. Refer to System Operation, Testing and Adjusting, "Fuel System - Prime".
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that the mating surfaces of fuel injection pump (1) and fuel transfer pump (2) are clean and free from damage.
Illustration 1 g01335045
Install a new O-ring seal (11) to fuel transfer pump (2) . Lubricate the O-ring seal with clean engine oil.
Illustration 2 g01335043
Align the holes in fuel transfer pump (2) with dowels (10) in fuel injection pump (1) . Install the fuel transfer pump to the fuel injection pump.
Illustration 3 g01334899
Use an allen wrench with a ball end to install the allen head screws (3) . Tighten the allen head screws to a torque of 30 N m (22 lb ft).
Remove the plugs and the caps from the ports and tube assemblies.
Install tube assembly (4) for the engine oil supply to fuel injection pump (1) . Install new washers to the banjo bolt for oil supply tube assembly. Install the banjo bolt to the cylinder block. Tighten both connectors to a torque of 15 N m (11 lb ft).
Install tube assembly (8) for the fuel return to fuel transfer pump (2) and to the cylinder head. Tighten both banjo bolts to a torque of 21 N m (15 lb ft).
Install a new O-ring seal to connector (6) . Install connector (6) to fuel transfer pump (2) . Tighten the connector to torque of 15 N m (11 lb ft).
If necessary, install a new O-ring seal to connector (9) and install connector (9) to fuel transfer pump (2) . Tighten the connector to torque of 15 N m (11 lb ft).
Connect plastic tube assembly (5) to the outlet of fuel transfer pump (2) .
Install plastic tube assembly (7) to fuel transfer pump (2) .
Turn the fuel supply to the ON position.
Remove the air from the fuel system. Refer to System Operation, Testing and Adjusting, "Fuel System - Prime".
Caterpillar parts catalog:
Parts shank Caterpillar catalog:
D10N, D9R
D10N, D10R, D10T, D10T2, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
4Z8937
SHANK AS-RIPPER
D10R, D10T, D10T2
D10R, D10T, D10T2
1093135
SHANK AS-RIPPER
D10R, D10T, D10T2
D10R, D10T, D10T2
D10R, D10T, D10T2, D11R
8E8413
SHANK AS-RIPPER
D11N, D11R, D11T
D11N, D11R, D11T
4Z8937
SHANK AS-RIPPER
D10R, D10T, D10T2
D10R, D10T, D10T2
4Z9314
SHANK AS-RIPPER
D11R, D11T
D11R, D11T
4Z9312
SHANK AS-RIPPER
D11R, D11T
D11R, D11T
4Z8849
SHANK AS
D11R, D11T
D11R, D11T
4Z9197
SHANK-RIPPER
D11R
D11R
1049275
SHANK AS-RIPPER
D11N, D11R, D11T
D11N, D11R, D11T
D11N, D11R, D11T