SPIDER 4V5392 - Caterpillar

3114, 3116, 3126, 3208, 3304, 3306, 3406, 3408, Or 3412 Commercial Engines With Mechanical Fuel SystemsStarting in 1996, the EPA Emission Regulations require engines to be equipped with some type of tamper resistant device. All the above Emission Certified Mechanical Fuel System Engines will be equipped with tamper resistant bolts or a tamper resistant plug in the governor housing to NOT ALLOW UNAUTHORIZED changes to the AFRC setting. The following is a listing of the devices used by each engine size.
The 3114, 3116, and 3126 Engines will have a tamper resistant plug in the governor housing to NOT ALLOW UNAUTHORIZED changes to the AFRC setting. There are two sizes of tamper resistant plugs being used. Illustration 1 shows the typical location of a 128-4786 Tamper Resistant Plug (7/8inch thread). Illustration 2 shows the typical location of a 128-4794 Tamper Resistant Plug (1 5/8inch thread). If an adjustment is required on a 3114, 3116, or 3126 Engine equipped with a tamper resistant plug, a 131-5009 Wrench is required to remove and install the tamper resistant plug.
Illustration 1. Typical location of a 128-4786 Tamper Resistant Plug (7/8inch thread) in a governor housing.
Illustration 2. Typical location of a 128-4794 Tamper Resistant Plug (1 5/8inch thread) in a governor housing.The 3208 Commercial Engines will have the new 128-7792 and 128-7795 Tamper Resistant Bolts on the AFRC and cover. Illustration 3 shows the locations of the new tamper resistant bolts.
Illustration 3. Locations of the new 128-7792 (1) and 128-7795 (2) Tamper Resistant Bolts on 3208 Commercial Engines.The 3304 and 3306 Commercial Engines will have new 128-7794 and 128-7796 Tamper Resistant Bolts on the AFRC and cover. Illustration 4 shows the location of the new tamper resistant bolts.
Illustration 4. Location of the new 128-7794 (3) and 128-7796 (4) Tamper Resistant Bolts on 3304 and 3306 Commercial Engines.The 3406 Commercial Engines with mechanical fuel systems will have new 128-7794 and 128-7796 Tamper Resistant Bolts on the AFRC and cover. Illustration 5 shows the location of the new tamper resistant bolts.
Illustration 5. Location of the new 128-7794 (3) and 128-7796 (4) Tamper Resistant Bolts on 3406 Commercial Engines with mechanical fuel systems.The 3408 and 3412 Commercial Engines with mechanical fuel systems will have new 128-7793 and 128-7798 Tamper Resistant Bolts on the AFRC and cover. Illustration 6 shows the location of the new tamper resistant bolts. In certain applications, when a dash pot is used, one longer 128-7799 Tamper Resistant Bolt is used in place of the 128-7798 Tamper Resistant Bolt.
Illustration 6. Location of the new 128-7793 (5) and 128-7798 (6) Tamper Resistant Bolts on 3408 and 3412 Commercial Engines with mechanical fuel systems. Tamper Resistant Bolt Removal And Installation
If an adjustment is required on a 3208, 3300, or 3400 Engine equipped with tamper resistant bolts, the bolts must be removed. Use the procedure that follows to remove the tamper resistant bolts:
1. Use a 1U-5592 (118 degree) Drill Bit or a 1U-5634 (135 degree split point) Drill Bit to drill a 7/64inch hole in the center