1570932 SPRING Caterpillar parts
345B, 345B II, 345B II MH, 345B L, 345C MH, W345B II
Rating:
Alternative (cross code) number:
CA1570932
157-0932
1570932
CA1570932
157-0932
1570932
Information:
ACTUAL RATE
20
N/MM
FREE LENGTH
72
mm
OD
12.7
mm
SOLID LENGTH
50.6
mm
WIRE DIAMETER
2.5
mm
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$41.25
29 Mar 2024
1.0[0.45] pounds
US: Chobitok
UYSB 3 Tier Layer Rolling Cart Storage Home Furniture Rack Shelves Metal Space Save Organization and storage Book shelves Office decor Wall shelf Storage shelves Wall shelves
Color: Black Bedroom wall decor Bathroom wall decor Closet organizer Shelves for storage Garage shelving Closet shelves Shelves for bedroom Hanging shelves Metal shelves Shelving unit Pantry shelves || Easy to install Kitchen shelves Storage shelf Cubby shelving Storage rack Shelves for wall || Made of high quality iron, sturdy and dura ble || Material: Iron
Color: Black Bedroom wall decor Bathroom wall decor Closet organizer Shelves for storage Garage shelving Closet shelves Shelves for bedroom Hanging shelves Metal shelves Shelving unit Pantry shelves || Easy to install Kitchen shelves Storage shelf Cubby shelving Storage rack Shelves for wall || Made of high quality iron, sturdy and dura ble || Material: Iron
$32.96
08 Feb 2018
150 Hundredths Pounds
Dorman: Dorman
Dorman 1570932 Jeep Grand Cherokee Driver Side Fog Light
DOT compliant to ensure quality standards for safety||Durable against the elements and against poor road conditions||Replacement of worn or damaged fog light restores aesthetic appearance||Direct replacement for a proper fit every time
DOT compliant to ensure quality standards for safety||Durable against the elements and against poor road conditions||Replacement of worn or damaged fog light restores aesthetic appearance||Direct replacement for a proper fit every time
Number on catalog scheme:
16
For full view, you need register
Compatible equipment models: 1570932:
Information:
Clean the cooling system and flush the cooling system before the recommended maintenance interval if the following conditions exist:
The engine overheats frequently.
Foaming is observed.
The oil has entered the cooling system and the coolant is contaminated.
The fuel has entered the cooling system and the coolant is contaminated.Note: When the cooling system is cleaned, only clean water is needed when the ELC is drained and replaced.Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This inspection is a good opportunity to replace the water pump, the water temperature regulator, and the hoses, if necessary. Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Cat dealer or consult Dealer Service Tools.Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques. Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with Extended Life Coolant (ELC). Refer to this Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section) for more information on cooling system specifications. Do not install the cooling system filler cap.
Start and run the engine at low idle. Increase the
The engine overheats frequently.
Foaming is observed.
The oil has entered the cooling system and the coolant is contaminated.
The fuel has entered the cooling system and the coolant is contaminated.Note: When the cooling system is cleaned, only clean water is needed when the ELC is drained and replaced.Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This inspection is a good opportunity to replace the water pump, the water temperature regulator, and the hoses, if necessary. Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Cat dealer or consult Dealer Service Tools.Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques. Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with Extended Life Coolant (ELC). Refer to this Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section) for more information on cooling system specifications. Do not install the cooling system filler cap.
Start and run the engine at low idle. Increase the
Caterpillar parts catalog:
Parts spring Caterpillar catalog:
1297942
SPRING
345B, 345B II, 345B II MH, 345B L, W345B II
345B, 345B II, 345B II MH, 345B L, W345B II
1232538
SPRING
345B II, 345B L
345B II, 345B L
330C, 330C FM, 345B, 345B II, 345B II MH, 345B L
1540580
SPRING
330B L
330B L
330B, 330B L, W330B
330B, 330B L, 345B, 345B L, W330B
1227718
SPRING
345B II, 345B L
345B II, 345B L
1796701
SPRING
345B II, 345B L
345B II, 345B L
345B II, 345B II MH, 345B L, W345B II
1373778
SPRING
345B, 345B L
345B, 345B L
1373779
SPRING
345B, 345B L
345B, 345B L
1574948
SPRING
345B, 345B II, 345B II MH, 345B L, 345C MH, W345B II
345B, 345B II, 345B II MH, 345B L, 345C MH, W345B II