2417313 STICK & BEARING AS Caterpillar parts
320D, 323D L, 323D LN, 323D SA
Rating:
Alternative (cross code) number:
CA2417313
241-7313
2417313
CA2417313
241-7313
2417313
EXCAVATOR,
Number on catalog scheme:
10
For full view, you need register
Information:
Installation Procedure For Conversion Kit
Illustration 1 g02083474
Typical former steering control unit (A) 12 point bolts (B) Machine end cap (C) Gerotor outer ring (D) Gerotor star (E) Spacer (F) Metering body (G) Square section ring
Remove 12 point bolts (A)
Remove machine end caps (B)
Remove gerotor outer ring (C) and square section ring (G)
Remove spacer (E)
Remove square section ring (G) from metering body (F)
Illustration 2 g02083613
Typical converted steering control unit (AA) six point bolts (BB) Ground steel end cap (C) Gerotor outer ring (D) Gerotor star (EE) Spacer (F) Metering body (GG) New round section o-ring
Install round cross section o-ring (GG) in groove of metering body (F.)
Install round cross section o-ring (GG) in groove of spacer (EE)
Install spacer (EE) with o-ring (GG) facing away from metering body (F)
Install gerotor outer ring (C) with o-ring (GG) facing away from metering body (F) Note: If, the gerotor star (D) has a full length spline you can turn the spline with the outer ring. If the star has a partial spline, turn the outer ring only.
Install round cross section o-ring (GG) in the groove of gerotor outer ring (C)
Install ground steel end cap (BB) with new, self sealing cap screws (AA)
Use a six point (E10) Torx drive to dry torque all seven bolts (AA) to 14.12 2.83 N m (10.41 2.09 lb ft). Then final torque to 28.25 2.83 N m (20.83 2.09 lb ft) in the sequence that is numbered 1 through 7 in the magnified view of illustration 2Shaft Seal Replacement For Low Input Torque Steering Units
Illustration 3 g02084883
Standard input torque steering control unit. (K) Shaft seal (P) Seal gland bushing without groovesNote: The shaft seal for this unit has not been replaced.
Illustration 4 g02085213
Low input torque steering control unit (M) Former three piece shaft seal (N) New one piece shaft seal (T) Grooves in seal gland bushingTo determine low or standard torque, examine the seal gland bushing for grooves. Grooves identify low torque units.Note: The new shaft seal for the former (low torque) metering pump groups, is included with the seal kit listed in the chart.
Illustration 1 g02083474
Typical former steering control unit (A) 12 point bolts (B) Machine end cap (C) Gerotor outer ring (D) Gerotor star (E) Spacer (F) Metering body (G) Square section ring
Remove 12 point bolts (A)
Remove machine end caps (B)
Remove gerotor outer ring (C) and square section ring (G)
Remove spacer (E)
Remove square section ring (G) from metering body (F)
Illustration 2 g02083613
Typical converted steering control unit (AA) six point bolts (BB) Ground steel end cap (C) Gerotor outer ring (D) Gerotor star (EE) Spacer (F) Metering body (GG) New round section o-ring
Install round cross section o-ring (GG) in groove of metering body (F.)
Install round cross section o-ring (GG) in groove of spacer (EE)
Install spacer (EE) with o-ring (GG) facing away from metering body (F)
Install gerotor outer ring (C) with o-ring (GG) facing away from metering body (F) Note: If, the gerotor star (D) has a full length spline you can turn the spline with the outer ring. If the star has a partial spline, turn the outer ring only.
Install round cross section o-ring (GG) in the groove of gerotor outer ring (C)
Install ground steel end cap (BB) with new, self sealing cap screws (AA)
Use a six point (E10) Torx drive to dry torque all seven bolts (AA) to 14.12 2.83 N m (10.41 2.09 lb ft). Then final torque to 28.25 2.83 N m (20.83 2.09 lb ft) in the sequence that is numbered 1 through 7 in the magnified view of illustration 2Shaft Seal Replacement For Low Input Torque Steering Units
Illustration 3 g02084883
Standard input torque steering control unit. (K) Shaft seal (P) Seal gland bushing without groovesNote: The shaft seal for this unit has not been replaced.
Illustration 4 g02085213
Low input torque steering control unit (M) Former three piece shaft seal (N) New one piece shaft seal (T) Grooves in seal gland bushingTo determine low or standard torque, examine the seal gland bushing for grooves. Grooves identify low torque units.Note: The new shaft seal for the former (low torque) metering pump groups, is included with the seal kit listed in the chart.
Caterpillar parts catalog:
Parts stick Caterpillar catalog:
2300280
STICK GP-HOE
320C, 320D
320C, 320D
2984127
STICK AR-HOE
320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L
320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L
2901789
STICK AR
323D L, 323D2 L
323D L, 323D2 L
2403846
STICK AR-HOE
320D, 320D L, 323D L, 323D LN
320D, 320D L, 323D L, 323D LN
3995413
STICK & BEARING AS
320D, 320D GC, 320D LRR, 320D RR, 320D2, 320D2 GC
320D, 320D GC, 320D LRR, 320D RR, 320D2, 320D2 GC
2909219
STICK GP-HOE
323D L, 323D LN
323D L, 323D LN
2417304
STICK & BEARING AS
320D, 320D FM, 320D L, 320D LRR, 323D L, 323D LN
320D, 320D FM, 320D L, 320D LRR, 323D L, 323D LN
2687133
STICK & BEARING AS
320C, 320D, 320D L
320C, 320D, 320D L
3645043
STICK & BEARING AS
320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 321D LCR, 323D L
320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 321D LCR, 323D L
2847325
STICK & BEARING AS
320D, 320D L, 320D LN, 320D LRR, 320D RR, 323D L, 323D LN, 323D SA
320D, 320D L, 320D LN, 320D LRR, 320D RR, 323D L, 323D LN, 323D SA
2417304
STICK & BEARING AS
320D, 320D FM, 320D L, 320D LRR, 323D L, 323D LN
320D, 320D FM, 320D L, 320D LRR, 323D L, 323D LN
2895957
STICK & BEARING AS
323D L
323D L
2614563
STICK & BEARING AS
1390, 2590, 541, 541 2, 551, 552, 552 2, TK741, TK751, TK752
1390, 2590, 541, 541 2, 551, 552, 552 2, TK741, TK751, TK752
2444236
STICK & BEARING AS
324D, 324D FM, 324D L, 324D LN
324D, 324D FM, 324D L, 324D LN
2909226
STICK & BEARING AS
323D L, 323D2 L
323D L, 323D2 L
2909220
STICK & BEARING AS
323D L, 323D LN
323D L, 323D LN
2909217
STICK & BEARING AS
323D L, 323D LN
323D L, 323D LN
2909211
STICK & BEARING AS
323D L, 323D LN
323D L, 323D LN
2417328
STICK & BEARING AS
323D L, 323D LN, 323D SA
323D L, 323D LN, 323D SA