1266916 SWITCH AS-PRESSURE Caterpillar parts
924G, 924GZ, 928HZ, 930G, AD45, AE40 II, IT14G, IT14G2, IT28G
Rating:
Alternative (cross code) number:
CA1266916
126-6916
1266916
CA1266916
126-6916
1266916
Weight: 0.16 pounds 0 kg.
Information:
ACTUATION PRESSURE
255 KPA
kPa
CONNECTOR TYPE
2-PIN DT
DEACTUATION PRESSURE
205 KPA
kPa
THREAD SIZE
.56-18
AMP.[RESISTIVE]
1.5A
CONTACT PRESSURE-MAX.
3500 KPA
CONATCT POSITION
NC
OPEN CYCLE LIFE
100000
SENSED MEDIA
OIL-FUEL-AIR
SUPPLY VOLTAGE
28V
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Compatible equipment models: 1266916:
Number on catalog scheme:
14
For full view, you need register
Information:
Which Generate This Code:This diagnostic code is recorded when the main display module does not receive expected information. For example, actual gear information is not received from other electronic control modules through the CAT data link. This diagnostic code causes the readouts, that are dependent upon the CAT data link information, to indicate abnormal values.The possible causes of this diagnostic code are listed in the order of probability:
A blown fuse
A poor electrical connection at a machine harness connector
A circuit in the CAT data link is shorted to ground.
The CAT data link circuit in the machine harness is shorted to the +battery circuit.
The CAT data link circuit in the machine harness is open.Ensure that the desired CID 0248 and FMI 09 is on hold. Ensure that the "SERV CODE" indicator shows "SERV CODE".Note: An electronic control module (ECM) which uses the CAT data link has failed.Test Step 1. CHECK FOR OTHER CODES.
Check other electronic control modules for a similar diagnostic code. Expected Result:Other diagnostic codes are showing.Results:
YES - Other diagnostic codes are showing.Repair: Exit this procedure and perform the procedures that are listed for the other diagnostic codes that are present. Stop.
NO - There are no other active diagnostic codes. Proceed to Test Step 2.Test Step 2. INSPECT THE HARNESS CONNECTORS.
Turn the key start switch and the disconnect switch to the OFF position.
Inspect the connections of the machine harness that are related to the CAT data link.
Make sure that connectors are clean and tight.Expected Result:The machine harness is correct.Results:
OK - The machine harness is correct. Proceed to Test Step 3.
NOT OK - The machine harness is not correct. Repair: Repair the machine harness or replace the machine harness. Stop.Test Step 3. CHECK FOR A SHORT TO GROUND.
The key start switch and the disconnect switch remains OFF.
Disconnect the machine harness from all electronic control modules that use the CAT data link.
At the machine harness connector for the main display module, measure the resistance between the CAT data link circuits (contacts 14 and 5) and all other contacts on the connector and frame ground.Expected Result:The resistance measurement should be greater than 5000 ohms.Results:
YES -
A blown fuse
A poor electrical connection at a machine harness connector
A circuit in the CAT data link is shorted to ground.
The CAT data link circuit in the machine harness is shorted to the +battery circuit.
The CAT data link circuit in the machine harness is open.Ensure that the desired CID 0248 and FMI 09 is on hold. Ensure that the "SERV CODE" indicator shows "SERV CODE".Note: An electronic control module (ECM) which uses the CAT data link has failed.Test Step 1. CHECK FOR OTHER CODES.
Check other electronic control modules for a similar diagnostic code. Expected Result:Other diagnostic codes are showing.Results:
YES - Other diagnostic codes are showing.Repair: Exit this procedure and perform the procedures that are listed for the other diagnostic codes that are present. Stop.
NO - There are no other active diagnostic codes. Proceed to Test Step 2.Test Step 2. INSPECT THE HARNESS CONNECTORS.
Turn the key start switch and the disconnect switch to the OFF position.
Inspect the connections of the machine harness that are related to the CAT data link.
Make sure that connectors are clean and tight.Expected Result:The machine harness is correct.Results:
OK - The machine harness is correct. Proceed to Test Step 3.
NOT OK - The machine harness is not correct. Repair: Repair the machine harness or replace the machine harness. Stop.Test Step 3. CHECK FOR A SHORT TO GROUND.
The key start switch and the disconnect switch remains OFF.
Disconnect the machine harness from all electronic control modules that use the CAT data link.
At the machine harness connector for the main display module, measure the resistance between the CAT data link circuits (contacts 14 and 5) and all other contacts on the connector and frame ground.Expected Result:The resistance measurement should be greater than 5000 ohms.Results:
YES -
Cat SIS web machinery list:
Parts switch Caterpillar catalog:
226B, 226B3, 232B, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247B, 247B3, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, 2...
3054C, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, 914G, C4.4, IT14G
3054C, 414E, 416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 914G, C4.4, IT14G
120M, 140M, 143H, 160M, 163H NA, 216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 242B, 242B3, 246C, 247B, 247B3, 24H, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 27...
320B, 322B, 322B L, 322C, 322C FM, 325B, 325B L, 330, 3306B, 330B, 330B L, 330C, 330C L, 3406C, 3412C, 345B L, 69D, 824G, 825G, 826G, 918F, 924F, 928F, 938F, 950G, 962G, 980G, AD40, AD45, AE40, AE40 I...
725, 730, 735, 740, AD40, AD45, AE40, AE40 II, C9, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX31-P600, CX35-C18I, R1700G, TH31-E61, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I, TH35-C15T, TH35-E81
525B, 535B, 725, 730, 735, 740, 924G, 924GZ, 953C, 963B, 963C, D5M, D6M, IT28G, R1600, R1600G, R1700 II, R1700G, R2900G, R3000H
924G, 924GZ, 930G, 938G II, IT28G, IT38G II
14H, 16H, 725, 730, 735, 740, 824G II, 824H, 834G, 834H, 844H, 854G, 854K, 924G, 924GZ, 924H, 924HZ, 928H, 928HZ, 930G, 938G II, 950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 98...
725, 725C, 730, 730C, 735, 735B, 740, 740B, 769D, 770, 771D, 772, 773D, 773E, 773F, 775D, 775E, 775F, 776D, 777D, 777F, 844H, 844K, 854K, 910K, 914G, 914K, 924H, 924HZ, 928HZ, 938G II, 938H, 980G II, ...
910G, 914G, 924G, 928G, 938G, IT14G, IT14G2, IT28G, IT38G
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 910G, 914G, 924G, 924GZ, 928G, 930G, 938G, 938G II, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H...
1076034
SWITCH AS
914G, 924G, 924GZ, 928G, IT14G, IT14G2, IT28G
914G, 924G, 924GZ, 928G, IT14G, IT14G2, IT28G
1780057
SWITCH AS-CONTROL
914G, IT14G, IT14G2
914G, IT14G, IT14G2
1076035
SWITCH AS-SPEED SELECT
910G, 914G, IT14G, IT14G2
910G, 914G, IT14G, IT14G2
1503754
SWITCH AS-PRESSURE
914G, IT14G, IT14G2, R2900G, R3000H
914G, IT14G, IT14G2, R2900G, R3000H
1076037
SWITCH AS-KICKOUT
914G, 924G, 924GZ, IT14G, IT14G2, IT28G, IT38G
914G, 924G, 924GZ, IT14G, IT14G2, IT28G, IT38G
1187237
SWITCH AS
914G, IT14G
914G, IT14G
1774479
SWITCH AS-PRESSURE
140G, 928G, IT28G
140G, 928G, IT28G
1852770
SWITCH AS-ROCKER
924G, 924GZ, 928G, IT28G, M325D L MH, M325D MH
924G, 924GZ, 928G, IT28G, M325D L MH, M325D MH
322B L, 325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 345C, 525C, 535C, 545C, 814F, 814F II, 815F, 815F II, 816F, 816F II, 824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 82...
1187238
SWITCH AS-NEUTRALIZER
924G, 924GZ, 928G, 938G, IT28G, IT38G
924G, 924GZ, 928G, 938G, IT28G, IT38G
1388140
SWITCH AS-PUSH BUTTON
815F, 815F II, 816F, 816F II, 938F, 950F II, 950G, 960F, 962G, 966F II, 966G, 970F, 972G
815F, 815F II, 816F, 816F II, 938F, 950F II, 950G, 960F, 962G, 966F II, 966G, 970F, 972G
1076067
SWITCH AS
IT14G, IT28G
IT14G, IT28G