2898490 TRACK-RUBBER Caterpillar parts
AP1055E, BG-2455D, BG1055E
Rating:
Alternative (cross code) number:
CA2898490
289-8490
2898490
CA2898490
289-8490
2898490
Weight: 879 pounds 399 kg.
ASPHALT PAVER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$7,526.29
24 Jan 2019
94000 Hundredths Pounds
ITR: ITR
ITR 2898490 RUBBER TRACK AP1055B
2898490 || 2898490 RUBBER TRACK AP1055B || AP1055B <b>Family</b>: Paver <b>Machine quantity</b>: 2 <b>Compatible machines</b>: Caterpillar - Paver - AP1055B Caterpillar - Paver - AP1055D Caterpillar - Paver - AP1055E Caterpillar - Paver - AP1055F Caterpillar - Paver - || P555F
2898490 || 2898490 RUBBER TRACK AP1055B || AP1055B <b>Family</b>: Paver <b>Machine quantity</b>: 2 <b>Compatible machines</b>: Caterpillar - Paver - AP1055B Caterpillar - Paver - AP1055D Caterpillar - Paver - AP1055E Caterpillar - Paver - AP1055F Caterpillar - Paver - || P555F
This part in 6 request:
Show.
This information for suppliers only!
2025-05-09
2025-02-19
2022-07-25
2022-06-17
2019-11-14
2017-12-10
Information:
System Operation Description:The throttle linkage should operate without binding or without excessive drag. When the throttle position sensor is not connected to the throttle, the throttle should return to low idle within one second. The calibration of the throttle position sensor requires the use of Caterpillar Electronic Technician (ET).
Illustration 1 g00726080
Test Step 1. Check and Adjust the Throttle Linkage.
Inspect the throttle linkage for components with the following conditions:
Loose
Bent
Broken
Missing
Worn
Place the engine control in the OFF/RESET mode.
Connect Cat ET to the service tool connector.
Place the engine control in the ON mode. Do not start the engine.
Observe the indication for the duty cycle on the "Monitor Throttle Position Sensor Signal" screen of Cat ET.
Place the throttle lever in the position for low idle. Adjust the throttle linkage. Adjust the low idle set screw.Expected Result:When the throttle is in low idle, the duty cycle is 5 to 10 percent. After the adjustment is completed, the duty cycle increases when the throttle lever is moved from the low idle position.Results:
OK - Proceed to test step 2.
Not OK - There is a problem with the throttle position sensor.Repair: Refer to Troubleshooting, "Throttle Postion Sensor Circuit -Test".STOPTest Step 2. Adjust the Throttle Linkage.
Place the throttle lever in the position of high idle. Adjust the throttle linkage. Adjust the high idle set screw.Expected Result:When the throttle is in high idle, the duty cycle is 90 to 95 percent. When the adjustment of the high idle is made on some types of linkage, the adjustment may change the low idle position. Repeat the adjustment for low idle in order to verify that the low idle is correctly adjusted.Results:
OK - The calibration was completed and verified.STOP
Not OK - The calibration was not completed and verified. There is a problem with the throttle position sensor.Repair: Refer to Troubleshooting, "Throttle Position Sensor Circuit - Test".STOP
Illustration 1 g00726080
Test Step 1. Check and Adjust the Throttle Linkage.
Inspect the throttle linkage for components with the following conditions:
Loose
Bent
Broken
Missing
Worn
Place the engine control in the OFF/RESET mode.
Connect Cat ET to the service tool connector.
Place the engine control in the ON mode. Do not start the engine.
Observe the indication for the duty cycle on the "Monitor Throttle Position Sensor Signal" screen of Cat ET.
Place the throttle lever in the position for low idle. Adjust the throttle linkage. Adjust the low idle set screw.Expected Result:When the throttle is in low idle, the duty cycle is 5 to 10 percent. After the adjustment is completed, the duty cycle increases when the throttle lever is moved from the low idle position.Results:
OK - Proceed to test step 2.
Not OK - There is a problem with the throttle position sensor.Repair: Refer to Troubleshooting, "Throttle Postion Sensor Circuit -Test".STOPTest Step 2. Adjust the Throttle Linkage.
Place the throttle lever in the position of high idle. Adjust the throttle linkage. Adjust the high idle set screw.Expected Result:When the throttle is in high idle, the duty cycle is 90 to 95 percent. When the adjustment of the high idle is made on some types of linkage, the adjustment may change the low idle position. Repeat the adjustment for low idle in order to verify that the low idle is correctly adjusted.Results:
OK - The calibration was completed and verified.STOP
Not OK - The calibration was not completed and verified. There is a problem with the throttle position sensor.Repair: Refer to Troubleshooting, "Throttle Position Sensor Circuit - Test".STOP
Caterpillar parts catalog:
Parts track Caterpillar catalog:
2675625
TRACK GP-RUBBER
AP1055E, BG-2455D, BG1055E
AP1055E, BG-2455D, BG1055E
2898492
TRACK GP-RUBBER
AP1055E, BG-2455D, BG1055E
AP1055E, BG-2455D, BG1055E
2940541
TRACK-RUBBER
AP-1055B, AP1055E, BG-2455D, BG1055E
AP-1055B, AP1055E, BG-2455D, BG1055E
2940601
TRACK-RUBBER
AP-655C, AP-655D, BG655D
AP-655C, AP-655D, BG655D
2940541
TRACK-RUBBER
AP-1055B, AP1055E, BG-2455D, BG1055E
AP-1055B, AP1055E, BG-2455D, BG1055E
1718701
TRACK SET-SEAT
CB-334D, CB-335D
CB-334D, CB-335D
1R1317
TRACK-RUBBER
AP-1055B, BG-2455C
AP-1055B, BG-2455C
0868657
TRACK-FREE
RR-250, SS-250
RR-250, SS-250
1V9856
TRACK
988B
988B
7X9030
TRACK
CS-551
CS-551
7X9011
TRACK
CS-551
CS-551
7X7129
TRACK GP
PR-750B
PR-750B
3525126
TRACK-RUBBER
AP555E
AP555E
3563363
TRACK-RUBBER
AP555E
AP555E
2898493
TRACK-RUBBER
AP-655D, BG655D
AP-655D, BG655D