2042161 ENGINE AR-COMPLETE Caterpillar parts
C-12
Rating:
Alternative (cross code) number:
CA2042161
204-2161
2042161
CA2042161
204-2161
2042161
TRUCK ENGINE,
Compatible equipment models: 2042161:
For full view, you need register
Information:
Removal Procedure
Start By:
Tilt the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Tilt the operator platform. Refer to Disassembly and Assembly, "Operator Platform - Tilt".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide"for tools and supplies to collect and contain fluids in Caterpillar machines.Dispose of all fluids according to local regulations.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00828948
Remove bolt (2) and pin assembly (3) from hydraulic cylinder (1) .
Illustration 2 g01946358
Disconnect hose assemblies (4) from hydraulic cylinder (1) .
Illustration 3 g00828952
Disconnect hose assembly (5) from hydraulic cylinder (1) .
Illustration 4 g00828953
Remove bolt (7) and pin assembly (6) from hydraulic cylinder (1). Remove hydraulic cylinder (1) from the machine.Installation Procedure
Illustration 5 g00828953
Install hydraulic cylinder (1), pin assembly (6), and bolt (7) .
Illustration 6 g00828952
Connect hose assembly (5) to hydraulic cylinder (1) .
Illustration 7 g01946358
Connect hose assemblies (4) to hydraulic cylinder (1) .
Illustration 8 g00828948
Install pin assembly (3) and bolt (2) to hydraulic cylinder (1) .
Start By:
Tilt the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Tilt the operator platform. Refer to Disassembly and Assembly, "Operator Platform - Tilt".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide"for tools and supplies to collect and contain fluids in Caterpillar machines.Dispose of all fluids according to local regulations.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00828948
Remove bolt (2) and pin assembly (3) from hydraulic cylinder (1) .
Illustration 2 g01946358
Disconnect hose assemblies (4) from hydraulic cylinder (1) .
Illustration 3 g00828952
Disconnect hose assembly (5) from hydraulic cylinder (1) .
Illustration 4 g00828953
Remove bolt (7) and pin assembly (6) from hydraulic cylinder (1). Remove hydraulic cylinder (1) from the machine.Installation Procedure
Illustration 5 g00828953
Install hydraulic cylinder (1), pin assembly (6), and bolt (7) .
Illustration 6 g00828952
Connect hose assembly (5) to hydraulic cylinder (1) .
Illustration 7 g01946358
Connect hose assemblies (4) to hydraulic cylinder (1) .
Illustration 8 g00828948
Install pin assembly (3) and bolt (2) to hydraulic cylinder (1) .
