2281285 ENGINE AR-COMPLETE Caterpillar parts
C-12
Rating:
Alternative (cross code) number:
CA2281285
228-1285
2281285
CA2281285
228-1285
2281285
TRUCK ENGINE,
Compatible equipment models: 2281285:
For full view, you need register
Information:
Bucket Operating Technique
Illustration 1 g01627645
Tactical monitor display (1) Front camera image (2) Rear camera image (3) Bucket position indicatorUse front camera image (1) and rear camera image (2) for loading, hauling and dumping the bucket.Note: Only use bucket position indicator (3) as a guide to the position of the bucket.Bucket Control Joystick
Illustration 2 g01627653
Typical example (4) Lower (5) Tilt back (6) Dump (7) RaiseUse the bucket control joystick to control bucket movements.Loading, Hauling and Dumping
Illustration 3 g01775793
Typical example
Position the bucket parallel to the ground. The bucket should barely skim the ground. Drive the bucket straight into the pile.
Illustration 4 g01627659
Raise position
Move the bucket control joystick control lever to the RAISE position as forward movement slows. Return to the HOLD position for additional tilt back power.
Illustration 5 g01775794
Typical example
To fill the bucket, move the bucket control joystick control lever back and forth from the TILT BACK position to the HOLD position while continuing to use RAISE position as required to reduce wheel slip.
Illustration 6 g01627660
Typical example
When the bucket is loaded, move the bucket control joystick control lever to the TILT BACK position.
Illustration 7 g01775795
Typical example
Raise the bucket high enough to clear the material being loaded. Tilt the bucket back until the bucket contacts the stops. Always carry the load with the bucket in the fully tilted back position to avoid material spillage and minimize loader linkage wear.Note: Do not overfill the bucket as it may affect the LADAR scans.
Move the motion control joystick to the REVERSE position. Carry the loaded bucket approximately 400 mm (15 inch) above the ground level.
Illustration 8 g01627659
Raise position
When reaching the dump area, move the bucket control joystick control lever to the RAISE position.
Illustration 9 g01627661
Dump position
When at the correct height, move the bucket control joystick control lever to the DUMP position.
To control dumping, move the bucket control joystick control lever to the DUMP position. Then, return the lever to the HOLD position. Repeat this procedure until the bucket is empty.
Illustration 10 g01775796
Typical example
To achieve the maximum angle for dumping, use the stops for the bucket.
Illustration 1 g01627645
Tactical monitor display (1) Front camera image (2) Rear camera image (3) Bucket position indicatorUse front camera image (1) and rear camera image (2) for loading, hauling and dumping the bucket.Note: Only use bucket position indicator (3) as a guide to the position of the bucket.Bucket Control Joystick
Illustration 2 g01627653
Typical example (4) Lower (5) Tilt back (6) Dump (7) RaiseUse the bucket control joystick to control bucket movements.Loading, Hauling and Dumping
Illustration 3 g01775793
Typical example
Position the bucket parallel to the ground. The bucket should barely skim the ground. Drive the bucket straight into the pile.
Illustration 4 g01627659
Raise position
Move the bucket control joystick control lever to the RAISE position as forward movement slows. Return to the HOLD position for additional tilt back power.
Illustration 5 g01775794
Typical example
To fill the bucket, move the bucket control joystick control lever back and forth from the TILT BACK position to the HOLD position while continuing to use RAISE position as required to reduce wheel slip.
Illustration 6 g01627660
Typical example
When the bucket is loaded, move the bucket control joystick control lever to the TILT BACK position.
Illustration 7 g01775795
Typical example
Raise the bucket high enough to clear the material being loaded. Tilt the bucket back until the bucket contacts the stops. Always carry the load with the bucket in the fully tilted back position to avoid material spillage and minimize loader linkage wear.Note: Do not overfill the bucket as it may affect the LADAR scans.
Move the motion control joystick to the REVERSE position. Carry the loaded bucket approximately 400 mm (15 inch) above the ground level.
Illustration 8 g01627659
Raise position
When reaching the dump area, move the bucket control joystick control lever to the RAISE position.
Illustration 9 g01627661
Dump position
When at the correct height, move the bucket control joystick control lever to the DUMP position.
To control dumping, move the bucket control joystick control lever to the DUMP position. Then, return the lever to the HOLD position. Repeat this procedure until the bucket is empty.
Illustration 10 g01775796
Typical example
To achieve the maximum angle for dumping, use the stops for the bucket.
