3308308 HARNESS AS-WIRING Caterpillar parts
Rating:
Alternative (cross code) number:
CA3308308
330-8308
3308308
CA3308308
330-8308
3308308
Weight: 3 pounds 1 kg.
Information:
Illustration 1 g00565249
The test for the water temperature contactor switch is a test for the temperature on the switch actuator and an electrical continuity test. This test will determine if the water temperature contactor switch is faulty and if the switch should be replaced. Use the 4C-6500 Digital Thermometer and the 4C-6500 Digital Thermometer for this test.
Install a probe from the 4C-6500 Digital Thermometer in the water manifold as close as possible to the water temperature contactor switch. Disconnect the connector for the water temperature contactor switch from the junction box.Note: Do not remove the water temperature contactor switch from the engine in order to conduct this test. The water temperature contactor switch uses the coolant flow and the coolant temperature in order to activate the switch at the actuation temperature.
When the water temperature contactor switch is disconnected from the junction box and the engine is stopped, check the continuity across the contact (WTS-3) and the common contact (WTS-2). Continuity should exist. This indicates that the circuit is closed across the contacts. Check the continuity across contact (WTS-1) and the common contact (WTS-2). Continuity should not exist. This indicates that the circuit is open across the contacts. If these conditions do not exist, the water temperature contactor switch is faulty and the switch needs to be replaced.
Start the engine. While the engine is running, place a load on the engine. Restrict the air flow to the engine. The engine should continue to run and the coolant temperature should increase to the actuation temperature of the water temperature contactor switch.
Observe the coolant temperature gauge in order to determine the temperature of the coolant when the actuation of the switch occurs. Compare the temperature on the gauge with the specifications for the water temperature contactor switch. The switch is actuated when the circuit across contacts (WTS-1) and (WTS-2) closes. The engine should shut down when the switch is actuated. This activates the protection system.
The actuation of the water temperature contactor switch may not occur when the temperature of the coolant is greater than the maximum value for the actuation temperature of the switch. Immediately reduce the load that is on the engine and remove the restriction to the air inlet. Allow the engine to run at idle until the temperature of the coolant returns to normal before you stop the engine.
The actual temperature of the coolant may not have been within the specifications of the water temperature contactor switch at the time of actuation. The switch is faulty and the switch needs to be replaced. Actuation might not occur when the temperature of the coolant is at the maximum. The switch is faulty and the switch needs to be replaced.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts harness Caterpillar catalog:
3308306
HARNESS AS-WIRING
Caterpillar
Caterpillar
3304772
HARNESS AS-WIRING
Caterpillar
Caterpillar
3287823
HARNESS AS-TRANSMISSION
Caterpillar
Caterpillar
3281548
HARNESS AS-LIGHTING
Caterpillar
Caterpillar
3260500
HARNESS AS-WIRING
Caterpillar
Caterpillar
3258147
HARNESS AS-LIGHTING
Caterpillar
Caterpillar
3404937
HARNESS AS-CAB
Caterpillar
Caterpillar
3404281
HARNESS AS-WIRING
Caterpillar
Caterpillar
3404280
HARNESS AS-RIDE CONTROL
Caterpillar
Caterpillar
3402295
HARNESS AS-RIDE CONTROL
Caterpillar
Caterpillar
3358042
HARNESS AS-CONSOLE
Caterpillar
Caterpillar
3323109
HARNESS-WIRING
Caterpillar
Caterpillar