1622302 KIT-CAP Caterpillar parts
301.5, 302.5, 303.5, 304.5, 307B, 312B L, 315B L, 317B LN, 318B, 320B, 322B LN, 325B L, 330B L, 345B II, 345B L, 350, 365B, 365B II, 375, 385B, 5080, 933C, 939C, D3C III, D4C III, D5C III, R1300, R130...
Rating:
Alternative (cross code) number:
CA1622302
162-2302
1622302
CA1622302
162-2302
1622302
Weight: 0.01 pounds 0 kg.
EXCAVATOR, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Cambro 1622302 Camtray 16" X 22" Rectangle Light Basketweave Case Qty 12
Cambro Use in restaurants, hotel room service, cafeterias, food courts, hospitals and schools
Cambro Use in restaurants, hotel room service, cafeterias, food courts, hospitals and schools
$179.96
29 Aug 2022
1.0[0.45] Pounds
US: MotoSport
ZERO GRAVITY Double Bubble Windscreen (Light Smoke) for 00-03 Kawasaki ZX9R
ZERO GRAVITY The Zero Gravity® Double Bubble® has changed the face of the sportbike industry. || This innovative "bubble within a bubble" concept was pioneered by Zero Gravity® and has pushed modern day race bikes to their peak performance level. || From Zero Gravity®'s first inception of a performance windscreen, the Double Bubble® is Zero Gravity's version of the now popular "stepped profile" design, pioneered by Zero Gravity Racing in the mid-90's. || Sculpted to the sport bike's distinctive futuristic lines, the Zero Gravity® Double Bubble® enhances the bike's race look while providing added aerodynamics. || Best optics of any windscreen on the market.
ZERO GRAVITY The Zero Gravity® Double Bubble® has changed the face of the sportbike industry. || This innovative "bubble within a bubble" concept was pioneered by Zero Gravity® and has pushed modern day race bikes to their peak performance level. || From Zero Gravity®'s first inception of a performance windscreen, the Double Bubble® is Zero Gravity's version of the now popular "stepped profile" design, pioneered by Zero Gravity Racing in the mid-90's. || Sculpted to the sport bike's distinctive futuristic lines, the Zero Gravity® Double Bubble® enhances the bike's race look while providing added aerodynamics. || Best optics of any windscreen on the market.
$359.99
23 May 2022
2.38[1.07] Pounds
US: Cook's Direct
Cambro 1622302 Camtray 16" X 22" Rectangle Light Basketweave Case qty 12
Cambro Use in restaurants, hotel room service, cafeterias, food courts, hospitals and schools
Cambro Use in restaurants, hotel room service, cafeterias, food courts, hospitals and schools
This part in 10 request:
Show.
This information for suppliers only!
2022-11-23
2022-04-13
2021-08-03
2020-11-23
2020-11-23
2020-11-23
2020-04-09
2019-09-26
2018-09-14
2016-05-04
Number on catalog scheme:
For full view, you need register
Compatible equipment models: 1622302:
Information:
Test Procedure
System Operation
The SLC 5/04 - 5/05 indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: input devices, output devices, wiring and the controller.The green "DH+" LED is flashing. There are no active nodes on the network.The red "DH+" LED is flashing. There are duplicate active nodes on the link with the same address.The red "FLT" LED is flashing during operation. The processor detects a major fault. The fault is in the processor expansion chassis or the fault is in the memory.
Illustration 1 g00563551
Diagram of the LED indicators
Illustration 2 g00562937
Central Processing Unit for typical systemFunctional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04 - 5/05.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Check the communication parameters of the customer supplied devices.
Check the communication parameter of the programmer.The results of the preceding procedure are in the following list:
The programmer address and the processor address are different. Proceed to 3.
The programmer address and the processor address are not different. Set the addresses. Verify that the repair resolves the problem. Stop.
Change the baud rate.
Change the baud rate of the programmer and change the baud rate of the processor.
Increase the maximum node address.Note: The default baud rate is 57,600. The default node address is one.The results of the preceding procedure are in the following list:
No errors are displayed on the LED indicators. Stop.
Errors are displayed on the LED indicators. Proceed to 4.
Check line voltage.
Measure the line voltage at the terminals.
Verify the voltage of the power supply. The power supply voltage should be measured between 21.0 VDC and 28.0 VDC.The results of the preceding procedure are in the following list:
The line voltage is in the range. Replace the processor. Verify that the repair solves the problem. Refer to Maintenance Procedure, "Processor - Replace".
The line voltage is out of the range. Refer to Troubleshooting, "System Power". Stop.
System Operation
The SLC 5/04 - 5/05 indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: input devices, output devices, wiring and the controller.The green "DH+" LED is flashing. There are no active nodes on the network.The red "DH+" LED is flashing. There are duplicate active nodes on the link with the same address.The red "FLT" LED is flashing during operation. The processor detects a major fault. The fault is in the processor expansion chassis or the fault is in the memory.
Illustration 1 g00563551
Diagram of the LED indicators
Illustration 2 g00562937
Central Processing Unit for typical systemFunctional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04 - 5/05.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Check the communication parameters of the customer supplied devices.
Check the communication parameter of the programmer.The results of the preceding procedure are in the following list:
The programmer address and the processor address are different. Proceed to 3.
The programmer address and the processor address are not different. Set the addresses. Verify that the repair resolves the problem. Stop.
Change the baud rate.
Change the baud rate of the programmer and change the baud rate of the processor.
Increase the maximum node address.Note: The default baud rate is 57,600. The default node address is one.The results of the preceding procedure are in the following list:
No errors are displayed on the LED indicators. Stop.
Errors are displayed on the LED indicators. Proceed to 4.
Check line voltage.
Measure the line voltage at the terminals.
Verify the voltage of the power supply. The power supply voltage should be measured between 21.0 VDC and 28.0 VDC.The results of the preceding procedure are in the following list:
The line voltage is in the range. Replace the processor. Verify that the repair solves the problem. Refer to Maintenance Procedure, "Processor - Replace".
The line voltage is out of the range. Refer to Troubleshooting, "System Power". Stop.
Cat SIS web machinery list:
Parts kit Caterpillar catalog:
345B II, 345B L, 345C, 350
330C, 345B II, 345B L, 350, M325C MH, M325D L MH
330, 330B L, 345B II, 345B L
330B, 330B L, 345B, 345B L
325B L, 345B L
330B L, 345B II, 345B L, 365B, 365B II, 385B
325B L, 328D LCR, 330B, 330B L, 345B L
345B II, 345B L
345B II, 345B L, 365B
345B II, 345B L, 365B
365B, 365B L
345B II, 345B II MH, W345B II
312B L, 315B L, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B L
1347059
KIT-SPOOL
312B L, 315B L, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B L
312B L, 315B L, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B L
2290969
KIT-SEAL
312B L, 313B, 315B L, 317B LN, 318B
312B L, 313B, 315B L, 317B LN, 318B
311B, 311C, 311D LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315B, 315B L, 315C, 31...
1916772
KIT-SEAL
307B, 307C, 312B L, 312C, 315B L, 315C, 317B LN, 318B
307B, 307C, 312B L, 312C, 315B L, 315C, 317B LN, 318B
1640703
KIT-VALVE
312B L
312B L
2054015
KIT-PLUNGER
312B L, 315B L, 317B LN, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 5110B, 539, M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D,...
312B L, 315B L, 317B LN, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 5110B, 539, M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D,...
1857914
KIT-PLUNGER
312B L, 315B L, 317B LN, 318B
312B L, 315B L, 317B LN, 318B
1857915
KIT-PLUNGER
312B L, 315B L, 317B LN, 318B
312B L, 315B L, 317B LN, 318B
312B L, 315B L, 317B LN, 318B, 320B, 322B L, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 933C, 939C, D3C III, D4C III, D5C III, M325B, W330B, W345B II
312B L, 315B L, 317B LN, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, M325B, W330B, W345B II
1627399
KIT-PLUNGER
312B L, 315B L, 317B LN, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, M325B, W330B, W345B II
312B L, 315B L, 317B LN, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, M325B, W330B, W345B II