BNJPJ00 Lafayette 3616 Engine Caterpillar parts
G3616
Rating:
Alternative (cross code) number:
CABNJPJ00
BNJ-PJ00
BNJPJ00
CABNJPJ00
BNJ-PJ00
BNJPJ00
GAS ENGINE,
Compatible equipment models: BNJPJ00:
For full view, you need register
Information:
You must read and understand the warnings and instructions contained in the Safety section of this manual before performing any operation or maintenance procedures.Hydraulic System
Look at the Oil Level
Backhoe - Position the machine on level ground, with the stick and bucket cylinders fully extended and the equipment lowered. Clamshell - Position the machine on level ground with the stick cylinder fully extended and the clamshell bucket open on the ground.1. Check the level with the hydraulic oil cold and the engine stopped. 2. Open the front access door on the right side. 3. Maintain the oil level to the FULL mark in the sight gauge (1).4. To add oil, remove the fill cap (2) slowly to relieve pressure.5. Replace the cap gasket if it is damaged. Install the fill cap and close the access door.Swing Gear
Lubricate Fitting
Fitting located in the cab. Rotate the upper structure 720° (two full rotations). Stop at each 90° (1/4 turn) and lubricate the swing gear through the left grease fitting. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material.Swing Bearing
Lubricate the Fitting
Fitting located in the cab. Rotate the upper structure 720° (two full rotations). Stop at each 90° (1/4 turn) and lubricate the bearing through the right fitting. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material. Lubricate until grease can be seen flowing from behind the bearing seal. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material.Boom and Stick
Lubricate the Fittings
Lubricate two fittings at the head end of the boom cylinders. Lubricate one fitting at the rod end of each boom cylinder (two fittings total). Lubricate one fitting at the boom to stick bearing. Lubricate one fitting at the rod end of the stick cylinder. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material.Backhoe Linkage
Lubricate Fittings
Lubricate one fitting at the head end of the bucket cylinder. Lubricate one fitting at the rod end of the bucket cylinder, two fittings on the stick and one fitting on the power link. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material.
Look at the Oil Level
Backhoe - Position the machine on level ground, with the stick and bucket cylinders fully extended and the equipment lowered. Clamshell - Position the machine on level ground with the stick cylinder fully extended and the clamshell bucket open on the ground.1. Check the level with the hydraulic oil cold and the engine stopped. 2. Open the front access door on the right side. 3. Maintain the oil level to the FULL mark in the sight gauge (1).4. To add oil, remove the fill cap (2) slowly to relieve pressure.5. Replace the cap gasket if it is damaged. Install the fill cap and close the access door.Swing Gear
Lubricate Fitting
Fitting located in the cab. Rotate the upper structure 720° (two full rotations). Stop at each 90° (1/4 turn) and lubricate the swing gear through the left grease fitting. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material.Swing Bearing
Lubricate the Fitting
Fitting located in the cab. Rotate the upper structure 720° (two full rotations). Stop at each 90° (1/4 turn) and lubricate the bearing through the right fitting. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material. Lubricate until grease can be seen flowing from behind the bearing seal. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material.Boom and Stick
Lubricate the Fittings
Lubricate two fittings at the head end of the boom cylinders. Lubricate one fitting at the rod end of each boom cylinder (two fittings total). Lubricate one fitting at the boom to stick bearing. Lubricate one fitting at the rod end of the stick cylinder. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material.Backhoe Linkage
Lubricate Fittings
Lubricate one fitting at the head end of the bucket cylinder. Lubricate one fitting at the rod end of the bucket cylinder, two fittings on the stick and one fitting on the power link. Lubricate Every 10 Service Hours or Daily when operating in water or abrasive material.