1371296 PUMP GP-GEAR Caterpillar parts
D3C III, D3G, D4C III, D4G, D5C III, D5G
Rating:
Alternative (cross code) number:
CA1371296
137-1296
1371296
CA1371296
137-1296
1371296
Weight: 8 pounds 3 kg.
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1371296 Gear Pump for Model D3C III, D3G, D4C III, D4G, D5C III, D5G Hydraulic
CTP For Hydraulic Pump || For Model D3C III, D3G, D4C III, D4G, D5C III, D5G || Easy in-and-out fit
CTP For Hydraulic Pump || For Model D3C III, D3G, D4C III, D4G, D5C III, D5G || Easy in-and-out fit
CTP 1371296 Gear Pump for Model D3C III, D3G, D4C III, D4G, D5C III, D5G Hydraulic
CTP For Hydraulic Pump || For Model D3C III, D3G, D4C III, D4G, D5C III, D5G || Easy in-and-out fit
CTP For Hydraulic Pump || For Model D3C III, D3G, D4C III, D4G, D5C III, D5G || Easy in-and-out fit
Compatible equipment models: 1371296:
Information:
Threads in bolt holes can become damaged from cross threading, loose parts and using damaged bolts. Retapping the hole will not give the quality of thread that is needed to meet torque specifications in most applications.
Heli-Coil inserts and installation tools have been released for making repairs to damaged threads. Heli-Coil inserts are available in most fine and coarse pitch, unified and metric size threads. A wall chart, Form SMHS8438, gives Heli-Coil sizes and tools needed to install Heli-Coil inserts.
The lengths of all Heli-Coil inserts, except the 6V9074 Insert and 6V9076 Insert, are one and one-half times their diameters. The lengths of the 6V9074 Insert and 6V9076 Insert are two times their diameters. The inserts may be cut to a shorter length or multiple inserts may be stacked if required lengths are not standard.
Hole Preparation
1. Use the wall chart to find the correct drill size. Drill the hole that has the damaged threads. The drill depths suggested allow for tap end clearance, countersink, and chamfer of the top. These depths are minimum and should be increased when possible. On thread relieved holes, such as head bolt threads in the cylinder block, depths should be held from the bottom of the counterbore. It is recommended that a magnetic base drill, drill press or radial drill be used when possible, especially with larger diameter holes.2. Countersink the drilled hole using a countersink with an included angle of 120°. Countersinking is not required on thread relieved holes.3. Tap the drilled hole using the tap and depth shown in the chart. Installation Of Coarse Thread Inserts
1. Screw the insert on the installation tool with the tang toward the front. Install the insert on the tool until the tang engages the driving contour of the tool.2. Position the tool and insert squarely over the tapped hole.3. Rotate the tool, exerting slight pressure against the work, until the insert is engaged in the tapped hole. Continue to rotate the tool until the insert is one-fourth to one-half thread below the top surface. On thread relieved holes, install the insert to the depth of the original thread. Installation Of Fine Thread Inserts
1. The tool to install fine thread inserts has two parts, the body and mandrel.2. Remove the mandrel from the body. Place the insert on the mandrel and engage the tang on the driving contour of the mandrel.3. Install the insert and mandrel into the tool body. Rotate the mandrel until two threads of the insert are engaged in the tool body.4. Place the tool squarely against the tapped hole. Rotate the mandrel, while holding the body of the tool with one hand, until the insert is one-fourth to one-half thread below the top surface. On thread relieved holes, install the insert to the original thread depth. Do not hold the tool body tightly against the work surface. Allow the tool to float. Tang Removal
The tang must be removed after the insert is installed to allow the bolt to be engaged to the correct depth.
On
Heli-Coil inserts and installation tools have been released for making repairs to damaged threads. Heli-Coil inserts are available in most fine and coarse pitch, unified and metric size threads. A wall chart, Form SMHS8438, gives Heli-Coil sizes and tools needed to install Heli-Coil inserts.
The lengths of all Heli-Coil inserts, except the 6V9074 Insert and 6V9076 Insert, are one and one-half times their diameters. The lengths of the 6V9074 Insert and 6V9076 Insert are two times their diameters. The inserts may be cut to a shorter length or multiple inserts may be stacked if required lengths are not standard.
Hole Preparation
1. Use the wall chart to find the correct drill size. Drill the hole that has the damaged threads. The drill depths suggested allow for tap end clearance, countersink, and chamfer of the top. These depths are minimum and should be increased when possible. On thread relieved holes, such as head bolt threads in the cylinder block, depths should be held from the bottom of the counterbore. It is recommended that a magnetic base drill, drill press or radial drill be used when possible, especially with larger diameter holes.2. Countersink the drilled hole using a countersink with an included angle of 120°. Countersinking is not required on thread relieved holes.3. Tap the drilled hole using the tap and depth shown in the chart. Installation Of Coarse Thread Inserts
1. Screw the insert on the installation tool with the tang toward the front. Install the insert on the tool until the tang engages the driving contour of the tool.2. Position the tool and insert squarely over the tapped hole.3. Rotate the tool, exerting slight pressure against the work, until the insert is engaged in the tapped hole. Continue to rotate the tool until the insert is one-fourth to one-half thread below the top surface. On thread relieved holes, install the insert to the depth of the original thread. Installation Of Fine Thread Inserts
1. The tool to install fine thread inserts has two parts, the body and mandrel.2. Remove the mandrel from the body. Place the insert on the mandrel and engage the tang on the driving contour of the mandrel.3. Install the insert and mandrel into the tool body. Rotate the mandrel until two threads of the insert are engaged in the tool body.4. Place the tool squarely against the tapped hole. Rotate the mandrel, while holding the body of the tool with one hand, until the insert is one-fourth to one-half thread below the top surface. On thread relieved holes, install the insert to the original thread depth. Do not hold the tool body tightly against the work surface. Allow the tool to float. Tang Removal
The tang must be removed after the insert is installed to allow the bolt to be engaged to the correct depth.
On
Caterpillar SIS machinery equipment:
Caterpillar SIS
D3C & D3C LGP,XL Series III Tractors Power Shift 6SL00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D4C & D4C LGP, Series XL SERIES III TRACTORS Power Shift 1FW00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D5C D5C LGP XL Series III Tractors Power Shift 6ZL00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D3C & D3C LGP, XL Series III Hystat Tractors 4KS00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D4C & D4C LGP, XL Series III Hystat Tractors 4LS00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D5C & D5C LGP, XL Series III Hystat Tractors 5HS00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D3G XL & LGP TRACK TYPE TRACTORS CFC00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D4G XL & LGP TRACK TYPE TRACTORS CFN00001-01071 (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D5G XL & LGP TRACK TYPE TRACTORS FDH00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D3G XL & D3G LGP Track-Type Tractors BYR00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D4G XL & D4G LGP Track-Type Tractors HYD00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D5G XL & D5G LGP Track-Type Tractors RKG00001-UP (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
D5C Series III Tractor Direct Drive Power Shift 9DL02550-02569 (MACHINE) POWERED BY 3046 Engine »
137-1296
PUMP GP-GEAR
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
2289129
PUMP GP-FUEL PRM & PRIM FILTER
414E, 416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, D3G, D4G, D5G
414E, 416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, D3G, D4G, D5G
3491063
PUMP GP-FUEL PRM & PRIM FILTER
414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, D3G, D4G, D5G
414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, D3G, D4G, D5G
1166724
PUMP GP-WATER
315, 315B, 315B FM L, 315C, 317B LN, 318B, D3C III, D3G, D4C III, D4G, D5C III, D5G
315, 315B, 315B FM L, 315C, 317B LN, 318B, D3C III, D3G, D4C III, D4G, D5C III, D5G
1455291
PUMP GP-CHARGE
939C, D4C III, D5C III
939C, D4C III, D5C III
2213667
PUMP GP-PISTON
D4G, D5G
D4G, D5G
1471476
PUMP GP-CHARGE
D4C III, D5C III
D4C III, D5C III
1451077
PUMP GP-CHARGE
CX35-P800, D3C III, D6N, D6T, D6T LGP, D6T LGPPAT, D6T XL, TH31-E61, TH35-E81
CX35-P800, D3C III, D6N, D6T, D6T LGP, D6T LGPPAT, D6T XL, TH31-E61, TH35-E81
1068263
PUMP GP-WATER
933, 933C, 939, 939C, D3C III, D4C III, D5C III
933, 933C, 939, 939C, D3C III, D4C III, D5C III
1072473
PUMP AS-WATER
3044C, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
3044C, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
1175033
PUMP AS-WATER
315, 315B, 315C, 317B LN, 318B, D3C III, D3G, D4C III, D4G, D5C III, D5G
315, 315B, 315C, 317B LN, 318B, D3C III, D3G, D4C III, D4G, D5C III, D5G
3224956
PUMP-WASHER
301.6C, 302.5C, 308E2 CR, 906H2, 907H2, 908H2, D3G, D4G, D5G
301.6C, 302.5C, 308E2 CR, 906H2, 907H2, 908H2, D3G, D4G, D5G
1110263
PUMP AS-FUEL INJECTION
939, 939C, D5C III
939, 939C, D5C III
1720265
PUMP GP-GEROTOR
3508, 3508C, 3512, 3512B, 3516, 3516B
3508, 3508C, 3512, 3512B, 3516, 3516B
3584973
PUMP & MTG GP-GEAR
272D, 299D
272D, 299D
1035790
PUMP & MTG GP-HYDRAULIC
938F, 938G, 938G II, IT38F, IT38G, IT38G II
938F, 938G, 938G II, IT38F, IT38G, IT38G II
3760510
PUMP GP-FUEL INJECTION
5130B, 776D, 777B, 777C, 777D, 784C, 785, 785B, 785C, 789, 789B, 789C, 789D, D11N, D11R
5130B, 776D, 777B, 777C, 777D, 784C, 785, 785B, 785C, 789, 789B, 789C, 789D, D11N, D11R
2400144
PUMP GP-MAIN HYDRAULIC
M318C, M318C MH
M318C, M318C MH
3287358
PUMP GP-FUEL INJECTION
430E, CD-54, CP-433E, PS-150C
430E, CD-54, CP-433E, PS-150C
2825083
PUMP GP-WATER
586C, C9
586C, C9
3616571
PUMP GP-FUEL TRANSFER
416F, 430F, 432F, 434F, 444F, CB-44B, CB-54B, D3K2 LGP, D4K2 XL, D5K2 XL
416F, 430F, 432F, 434F, 444F, CB-44B, CB-54B, D3K2 LGP, D4K2 XL, D5K2 XL
7W0053
PUMP GP-ENGINE OIL
3508, 3508B, 3508C, 3512, 5130, 5130B, 776C, 776D, 777, 777B, 777C, 777D, 854G, 992G, D11N, D11R, G3508, G3508B, G3512, PM3508
3508, 3508B, 3508C, 3512, 5130, 5130B, 776C, 776D, 777, 777B, 777C, 777D, 854G, 992G, D11N, D11R, G3508, G3508B, G3512, PM3508
2N6702
PUMP GP-PRELUBE
D399, G399
D399, G399
2768020
PUMP GP-FUEL PRM & SEC FILTER
C15, C15 I6, C18, C18 I6
C15, C15 I6, C18, C18 I6