2160033 PUMP GP-MAIN HYDRAULIC Caterpillar parts
345B II, 345B II MH, W345B II
Rating:
Alternative (cross code) number:
CA2160033
216-0033
2160033
CA2160033
216-0033
2160033
Weight: 267 pounds 121 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Related part:
2160033
PUMP GP-HYD
10R1552
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Multiplex Modelsport USA 2160033 Model MA-8-2 Reed Switch, Rinse Area
Multiplex Genuine OEM replacement part || Manitowoc Beverage is a leader in the commercial beverage and service industry || Use genuine OEM parts for safety reliability and performance
Multiplex Genuine OEM replacement part || Manitowoc Beverage is a leader in the commercial beverage and service industry || Use genuine OEM parts for safety reliability and performance
Delfield 2160033 Switch Reed Rinse Area Mod
DELFIELD Genuine oem replacement part || Delafield has over 50-years of industry experience and provides commercial foodservice equipment || Use genuine oem parts for safety reliability and performance || Country of origin: United States
DELFIELD Genuine oem replacement part || Delafield has over 50-years of industry experience and provides commercial foodservice equipment || Use genuine oem parts for safety reliability and performance || Country of origin: United States
Delfield 2160033 Switch Reed Rinse Area Mod
DELFIELD Genuine oem replacement part || Delafield has over 50-years of industry experience and provides commercial foodservice equipment || Use genuine oem parts for safety reliability and performance || Country of origin: United States
DELFIELD Genuine oem replacement part || Delafield has over 50-years of industry experience and provides commercial foodservice equipment || Use genuine oem parts for safety reliability and performance || Country of origin: United States
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 2160033:
Information:
Removal Procedure
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the engine oil into a suitable container for storage or disposal.
Illustration 1 g00953188
Remove bolts (2) . Remove engine oil pan (1) and the gasket.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8C-8422 Sealant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00953188
Illustration 3 g00612810
Clean the mating surface of engine oil pan (1) and the cylinder block. Apply Tooling (A) to four areas on the sealing surface of the oil pan. The areas are Marked Location (Y) . The areas are at the corners of the oil pan in the following locations:
connecting joint of the front housing and the front of the cylinder block
connecting joint of the flywheel housing and the rear of the cylinder block
Place a new gasket and engine oil pan (1) on the cylinder block.
Tighten four Oil Pan Bolts (X) .
Start with Bolt (Z) and tighten all remaining bolts (2) in a counterclockwise sequence.
Tighten bolts (2) to a torque of 31 1 N m (23 1 lb ft).
Start again with Bolt (Z) and tighten all remaining bolts in a counterclockwise sequence.
Tighten bolts (2) again to a torque of 31 1 N m (23 1 lb ft).
Fill the engine with oil to the correct level. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the engine oil into a suitable container for storage or disposal.
Illustration 1 g00953188
Remove bolts (2) . Remove engine oil pan (1) and the gasket.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8C-8422 Sealant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00953188
Illustration 3 g00612810
Clean the mating surface of engine oil pan (1) and the cylinder block. Apply Tooling (A) to four areas on the sealing surface of the oil pan. The areas are Marked Location (Y) . The areas are at the corners of the oil pan in the following locations:
connecting joint of the front housing and the front of the cylinder block
connecting joint of the flywheel housing and the rear of the cylinder block
Place a new gasket and engine oil pan (1) on the cylinder block.
Tighten four Oil Pan Bolts (X) .
Start with Bolt (Z) and tighten all remaining bolts (2) in a counterclockwise sequence.
Tighten bolts (2) to a torque of 31 1 N m (23 1 lb ft).
Start again with Bolt (Z) and tighten all remaining bolts in a counterclockwise sequence.
Tighten bolts (2) again to a torque of 31 1 N m (23 1 lb ft).
Fill the engine with oil to the correct level. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".
Caterpillar SIS machinery equipment:
Caterpillar SIS
345B L Series II Excavators AGS00001-UP (MACHINE) POWERED BY 3176C Engine »
216-0033
PUMP GP-MAIN HYDRAULIC
345B Series II Material Handler APB00001-UP (MACHINE) POWERED BY 3176C Engine »
216-0033
PUMP GP-MAIN HYDRAULIC
W345B Series II Material Handlers ANJ00001-UP (MACHINE) POWERED BY 3176C Engine »
216-0033
PUMP GP-MAIN HYDRAULIC
345B & 345B L Series II Excavators AKJ00001-UP (MACHINE) POWERED BY 3176C Engine »
216-0033
PUMP GP-MAIN HYDRAULIC
345B Series II Excavators ALD00001-UP (MACHINE) POWERED BY 3176C Engine »
216-0033
PUMP GP-MAIN HYDRAULIC
345B Series II Material Handler DET00001-UP (MACHINE) POWERED BY 3176C Engine »
216-0033
PUMP GP-MAIN HYDRAULIC
345B Series II Excavator CCC00001-UP (MACHINE) POWERED BY 3176C Engine »
216-0033
PUMP GP-MAIN HYDRAULIC
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine »
216-0033
PUMP GP-MAIN HYDRAULIC
Caterpillar parts catalog:
Parts pump Caterpillar catalog:
140H, 143H, 14H, 160H, 163H, 16H, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 572R II, 65E, 725, 730, 75E, 814F, 815F, 816F, 85E, 95E, 966G II, 972G II, C-10, C-12, C12, CPT...
330C, 330C L, 345B II, 345B II MH, TK1051, W345B II
140H, 143H, 14H, 14M, 160H, 163H, 16H, 16M, 3176, 3176B, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365B II, 365B L, 572R II, 6...
3176B, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B L, 480, 65E, 725, 730, 75C, 75E, 85C, 85E, 95E, 966G II, C-10, C-12, R1600, R1600G, R1700 II, R1700G, W345B II
345B II, 345B II MH
3176B, 3176C, 345B, 345B II, 345B L, 480, 75, 75C, 85C, 85D, 966G II, 972G II, D7R II
3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B L, 480, 65E, 725, 730, 75E, 85E, 95E, 966G II, 972G II, C-10, C-12, D7R II, MTC835, R1600, R1600G, R1700G, W345B II
345B II, 345B II MH, W345B II
345B II
120G, 12G, 12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 214B, 235, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 3176C, 3196,...
120M, 120M 2, 12M, 140M, 140M 2, 14M, 160M, 160M 2, 16M, 215B, 215C, 215D, 219D, 225, 225D, 227, 229, 229D, 231D, 235B, 235C, 235D, 245, 245B, 245D, 311B, 311D LRR, 312, 312B L, 312C L, 312D, 312D L, ...
330C, 330C FM, 330C L, 330C MH, 345B II, 345B II MH, W345B II
1175127
PUMP GP-SUMP
3126, C7
3126, C7
1266623
PUMP & MTG GP-STEERING
30/30, DEUCE
30/30, DEUCE
1763131
PUMP GP-PISTON
AP-1055B
AP-1055B
7C7556
PUMP GP-AUXILIARY SEA WATER
3408, 3412
3408, 3412
2286875
PUMP GP-GEAR
330C MH
330C MH
7E2392
PUMP GP-AUXILIARY WATER
G3512, G3516
G3512, G3516