1399918 ENGINE AR-COMPLETE Caterpillar parts
C-12
Rating:
Alternative (cross code) number:
CA1399918
139-9918
1399918
CA1399918
139-9918
1399918
TRUCK ENGINE,
Compatible equipment models: 1399918:
For full view, you need register
Information:
Required Tools
Table 1
Required Tools
Tool Item Qty Part No Description
A 1 169-8373 Fluid Sampling Bottle Machine Preparation
Drive the machine to a smooth, horizontal surface.
Illustration 1 g03817465
Move propel lever (2) to the NEUTRAL position.
Press parking brake switch (4) in order to change the status of the parking brake to "engaged". When the parking brake status is "engaged", an LED next to the parking brake switch will be illuminated.
Press rpm decrease switch (3) on the throttle control once in order to operate the engine in low idle.
Illustration 2 g03704262
Shut off the engine. Either place machine power switch (5) in the OFF position or press and hold push to start switch (1) for 3 seconds. An LED next to the push to start switch will flash when the engine is in shutdown mode. Note: The engine may run for several minutes when placed in the shutdown mode.
If the engine was shut down using the push to start switch (1), move the machine power switch (5) to the OFF position.
Illustration 3 g03704274
Unhook latch (6) at the rear of the engine compartment and lift access panel (7).
Illustration 4 g03704283
Install prop rod (8).
Illustration 5 g03817476
Unhook latch (9), open access panel (10) on the right side of the machine. Test Procedure
Move machine power switch (5) to the ON position.
Press push to start switch (1) for 2 seconds in order to start the engine. An LED next to the push to start switch will flash when the engine is in start mode. When the engine has started, the LED will remain illuminated. Note: Only one attempt to start the engine is allowed per key cycle. A new key cycle is necessary in order to restart the process.
Illustration 6 g03704307
Remove the cap from S O S tap (12) in the base of hydraulic oil filter (11). Obtain an oil sample with Tool (A).
Shut off the engine. Either place machine power switch (5) in the OFF position or press and hold push to start switch (1) for 3 seconds. An LED next to the push to start switch will flash when the engine is in shutdown mode. Note: The engine may run for several minutes when placed in the shutdown mode.
If the engine was shut down using the push to start switch (1), move the machine power switch (5) to the OFF position.
Remove hydraulic oil filter (11). Check the hydraulic element for foreign materials.
Bronze-colored particles give an indication of pump failure or motor port plate failure.
Shiny steel particles give an indication of pump failure or motor piston failure.
Rubber particles indicate a seal failure or a hose failure.
Aluminum particles give an indication of a pump or motor failure. Check the following components: a material feed charge pump, a fan drive motor, a ventilation fan motor and a tamper drive motor. Note: If any of these particles are found in the filter element, all components of the hydraulic oil system must be cleaned. Do not use any damaged parts. Any damaged parts must be removed and new parts must be installed.
Replace hydraulic filter (11).
If
Table 1
Required Tools
Tool Item Qty Part No Description
A 1 169-8373 Fluid Sampling Bottle Machine Preparation
Drive the machine to a smooth, horizontal surface.
Illustration 1 g03817465
Move propel lever (2) to the NEUTRAL position.
Press parking brake switch (4) in order to change the status of the parking brake to "engaged". When the parking brake status is "engaged", an LED next to the parking brake switch will be illuminated.
Press rpm decrease switch (3) on the throttle control once in order to operate the engine in low idle.
Illustration 2 g03704262
Shut off the engine. Either place machine power switch (5) in the OFF position or press and hold push to start switch (1) for 3 seconds. An LED next to the push to start switch will flash when the engine is in shutdown mode. Note: The engine may run for several minutes when placed in the shutdown mode.
If the engine was shut down using the push to start switch (1), move the machine power switch (5) to the OFF position.
Illustration 3 g03704274
Unhook latch (6) at the rear of the engine compartment and lift access panel (7).
Illustration 4 g03704283
Install prop rod (8).
Illustration 5 g03817476
Unhook latch (9), open access panel (10) on the right side of the machine. Test Procedure
Move machine power switch (5) to the ON position.
Press push to start switch (1) for 2 seconds in order to start the engine. An LED next to the push to start switch will flash when the engine is in start mode. When the engine has started, the LED will remain illuminated. Note: Only one attempt to start the engine is allowed per key cycle. A new key cycle is necessary in order to restart the process.
Illustration 6 g03704307
Remove the cap from S O S tap (12) in the base of hydraulic oil filter (11). Obtain an oil sample with Tool (A).
Shut off the engine. Either place machine power switch (5) in the OFF position or press and hold push to start switch (1) for 3 seconds. An LED next to the push to start switch will flash when the engine is in shutdown mode. Note: The engine may run for several minutes when placed in the shutdown mode.
If the engine was shut down using the push to start switch (1), move the machine power switch (5) to the OFF position.
Remove hydraulic oil filter (11). Check the hydraulic element for foreign materials.
Bronze-colored particles give an indication of pump failure or motor port plate failure.
Shiny steel particles give an indication of pump failure or motor piston failure.
Rubber particles indicate a seal failure or a hose failure.
Aluminum particles give an indication of a pump or motor failure. Check the following components: a material feed charge pump, a fan drive motor, a ventilation fan motor and a tamper drive motor. Note: If any of these particles are found in the filter element, all components of the hydraulic oil system must be cleaned. Do not use any damaged parts. Any damaged parts must be removed and new parts must be installed.
Replace hydraulic filter (11).
If
