BBWSN00 Lafayette 3616 Engine Caterpillar parts
G3616
Rating:
Alternative (cross code) number:
CABBWSN00
BBW-SN00
BBWSN00
CABBWSN00
BBW-SN00
BBWSN00
GAS ENGINE,
Compatible equipment models: BBWSN00:
For full view, you need register
Information:
Engine Crankcase
Change Oil and Filter
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.
1. Remove the access panel located under the rear of the machine by loosening the bolts and sliding the panel out. 2. Open the drain valve (1). Allow the oil to drain into a container.3. Close the drain valve after all of the oil has drained.4. Remove and discard the used crankcase oil filter element (2). Make sure all of the old filter seal is removed from the filter base.5. Apply a thin coat of oil to the seal on the new filter element.6. Install the filter by hand only until the filter contacts the base. Tighten 3/4 turn more. There are rotation index marks on each new filter spaced 90° apart, to be used as a guide for tightening.7. Install the access cover. 8. Open the engine access cover. 9. Remove the fill plug (2) to add oil. See "Refill Capacities." Clean and install the plug.10. Always measure the oil with the dipstick (1) to make certain the quantity of oil added is correct.11. Maintain the oil between the marks on the dipstick.12. Close the access cover.Belts - Fan and Alternator
Measure - Adjust
1. Inspect the condition and adjustment of the belts. If the belts are damaged, cracked or frayed, replace them in sets. 2. Measure the deflection of the belts. Apply approximately 110 N (25 lb.) force midway between the pulleys.Deflection should be 14 to 20 mm (9/16 to 13/16 inch). If deflection is not correct, loosen the alternator mounting bolts and adjust the belt.Look at the condition of the belt. Replace if cracked or frayed.Cooling System
Add Conditioner
At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Remove the fill cap only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand.Remove the fill cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Do not add coolant conditioner until you have read and understand the "Cooling System" material in the "Recommendations and Specifications" section.
1. Open the radiator fill cap access cover. 2. Remove the cap slowly to relieve pressure.3. Add .25 liters (1/2 pint) of liquid coolant conditioner.4. Install fill cap and close the access cover.Final Drives
Check Oil Level
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.
1. Remove the fill plug.2. Oil level should be to the bottom of the fill plug opening. Add oil if necessary.3. Install the fill plug.4. Repeat the procedure on the other final drive.
Change Oil and Filter
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.
1. Remove the access panel located under the rear of the machine by loosening the bolts and sliding the panel out. 2. Open the drain valve (1). Allow the oil to drain into a container.3. Close the drain valve after all of the oil has drained.4. Remove and discard the used crankcase oil filter element (2). Make sure all of the old filter seal is removed from the filter base.5. Apply a thin coat of oil to the seal on the new filter element.6. Install the filter by hand only until the filter contacts the base. Tighten 3/4 turn more. There are rotation index marks on each new filter spaced 90° apart, to be used as a guide for tightening.7. Install the access cover. 8. Open the engine access cover. 9. Remove the fill plug (2) to add oil. See "Refill Capacities." Clean and install the plug.10. Always measure the oil with the dipstick (1) to make certain the quantity of oil added is correct.11. Maintain the oil between the marks on the dipstick.12. Close the access cover.Belts - Fan and Alternator
Measure - Adjust
1. Inspect the condition and adjustment of the belts. If the belts are damaged, cracked or frayed, replace them in sets. 2. Measure the deflection of the belts. Apply approximately 110 N (25 lb.) force midway between the pulleys.Deflection should be 14 to 20 mm (9/16 to 13/16 inch). If deflection is not correct, loosen the alternator mounting bolts and adjust the belt.Look at the condition of the belt. Replace if cracked or frayed.Cooling System
Add Conditioner
At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Remove the fill cap only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand.Remove the fill cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Do not add coolant conditioner until you have read and understand the "Cooling System" material in the "Recommendations and Specifications" section.
1. Open the radiator fill cap access cover. 2. Remove the cap slowly to relieve pressure.3. Add .25 liters (1/2 pint) of liquid coolant conditioner.4. Install fill cap and close the access cover.Final Drives
Check Oil Level
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.
1. Remove the fill plug.2. Oil level should be to the bottom of the fill plug opening. Add oil if necessary.3. Install the fill plug.4. Repeat the procedure on the other final drive.