BKRHK00 Lafayette 3608 Engine Caterpillar parts
3608
Rating:
Alternative (cross code) number:
CABKRHK00
BKR-HK00
BKRHK00
CABKRHK00
BKR-HK00
BKRHK00
MARINE ENGINE,
Compatible equipment models: BKRHK00:
For full view, you need register
Information:
Required Parts
Table 1
Required Parts
Qty Part Number Part Name
2 096-0192 Lockwasher
2 096-2617 Screw
3 7K-1181 Cable Strap
1 3S-2093 Cable Strap
2 8T-0328 Hard Washer
1 450-7108 Radio As
1 467-4835 Radio Harness As Machine Preparation
Position the machine on level ground.
Release the hydraulic system pressure. Refer to the appropriate Operation and Maintenance Manual, "System Pressure Release" procedure for your machine.
Illustration 1 g00104545
Attach a "Do Not Operate" warning tag to the start switch before you service or repair the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Removal Procedure
Illustration 2 g06023627
Existing radio group (typical example)
(A) Cab
(B) Antenna cable
(C) Radio harness
(1) Harness connector
(2) Antenna cable jack
(3) Screws
(4) Radio
Remove the covers from right side console to gain access to the area around radio (4).
Disconnect antenna cable jack (2) from radio (4).
Remove two M5 screws (3).
Remove radio (4) from the right side console.Installation Procedure
Table 2
Required Parts
Item Qty Part Number Part Name
1 2 096-0192 Lockwasher
2 2 096-2617 Screw
3 3 7K-1181 Cable Strap
4 1 3S-2093 Cable Strap
5 2 8T-0328 Hard Washer
6 1 450-7108 Radio As
7 1 467-4835 Radio Harness As
Illustration 3 g06023980
(A) Console harness assembly
(B) Antenna cable
(C) Bracket
(1) 096-0192 Lockwasher
(2) 096-2617 Screw
(3) 7K-1181 Cable Strap
(4) 3S-2093 Cable Strap
(5) 8T-0328 Hard Washer
(6) 450-7108 Radio As
(7) 467-4835 Radio Harness As
Position new radio assembly (6) onto the existing bracket. Secure the radio assembly to the bracket using two new screws (2), to new lockwashers (1), and two new hard washers (5). Tighten the two screws to a maximum torque of 4 N m (35 lb in).
Connect new radio harness assembly (7) to the cab harness.
Connect the other end of radio harness assembly (7) to radio assembly (6).
Connect existing antenna cable to radio assembly (7).
Secure the red jack, the white jack, and the antenna cable by using one new cable strap (4).
Reinstall covers.
Table 1
Required Parts
Qty Part Number Part Name
2 096-0192 Lockwasher
2 096-2617 Screw
3 7K-1181 Cable Strap
1 3S-2093 Cable Strap
2 8T-0328 Hard Washer
1 450-7108 Radio As
1 467-4835 Radio Harness As Machine Preparation
Position the machine on level ground.
Release the hydraulic system pressure. Refer to the appropriate Operation and Maintenance Manual, "System Pressure Release" procedure for your machine.
Illustration 1 g00104545
Attach a "Do Not Operate" warning tag to the start switch before you service or repair the equipment. These warning tags (Special Instruction, SEHS7332) are available from your Caterpillar dealer.Removal Procedure
Illustration 2 g06023627
Existing radio group (typical example)
(A) Cab
(B) Antenna cable
(C) Radio harness
(1) Harness connector
(2) Antenna cable jack
(3) Screws
(4) Radio
Remove the covers from right side console to gain access to the area around radio (4).
Disconnect antenna cable jack (2) from radio (4).
Remove two M5 screws (3).
Remove radio (4) from the right side console.Installation Procedure
Table 2
Required Parts
Item Qty Part Number Part Name
1 2 096-0192 Lockwasher
2 2 096-2617 Screw
3 3 7K-1181 Cable Strap
4 1 3S-2093 Cable Strap
5 2 8T-0328 Hard Washer
6 1 450-7108 Radio As
7 1 467-4835 Radio Harness As
Illustration 3 g06023980
(A) Console harness assembly
(B) Antenna cable
(C) Bracket
(1) 096-0192 Lockwasher
(2) 096-2617 Screw
(3) 7K-1181 Cable Strap
(4) 3S-2093 Cable Strap
(5) 8T-0328 Hard Washer
(6) 450-7108 Radio As
(7) 467-4835 Radio Harness As
Position new radio assembly (6) onto the existing bracket. Secure the radio assembly to the bracket using two new screws (2), to new lockwashers (1), and two new hard washers (5). Tighten the two screws to a maximum torque of 4 N m (35 lb in).
Connect new radio harness assembly (7) to the cab harness.
Connect the other end of radio harness assembly (7) to radio assembly (6).
Connect existing antenna cable to radio assembly (7).
Secure the red jack, the white jack, and the antenna cable by using one new cable strap (4).
Reinstall covers.